Manage traces and protocols debug level using the GUI
Control trace collection, verbosity level, freeze periods, default settings, and protocols debug levels using the GUI.
Manage trace collection and protocol debug levels from Configure > Cluster Settings > Support. The screen includes the Traces and Protocols Debug Level sections.

Traces
The Traces section displays the current traces status, ensured free capacity and maximum traces size for backends and clients, verbosity level, and freeze period.
To modify the maximum traces size and the ensured free capacity, use the CLI. See Manage traces and protocols debug level using the CLI.
Disable traces
Disable traces to stop collecting tracing data on the cluster.
Procedure
From the menu, select Configure > Cluster Settings, and select the Support tab.
In the Traces section, select Disable traces. Then, in the confirmation message, select Yes.
To resume trace collection, select Enable traces.
Change traces verbosity level
The verbosity level determines the amount of information in the tracing data. Setting the verbosity level to high provides more troubleshooting detail but can consume more disk space.

Procedure
From the menu, select Configure > Cluster Settings, and select the Support tab.
In the Traces section, depending on the current verbosity level (low or high), select Change traces level to high or Change traces level to low.
Freeze traces
Freeze traces for a selected period to retain data for investigation.

Before you begin
Identify the trace period and its required retention time.
Procedure
From the menu, select Configure > Cluster Settings, and select the Support tab.
In the Traces section, select Freeze traces.
In the Freeze traces dialog, set the following properties:
Start: Set the start date and time of the trace period.
End: Set the end date and time of the trace period.
Retention: Set the retention period and its unit, for example, days.
Override: Turn on to replace an existing freeze period.
Select Save.
The Traces section displays the freeze start time, freeze end time, and the date until which the traces are retained.
Reset traces freeze
Clear the freeze period when the investigation is complete. The traces return to the standard rotation.

Procedure
From the menu, select Configure > Cluster Settings, and select the Support tab.
In the Traces section, select Reset traces freeze. Then, in the confirmation message, select Yes.
Restore traces default settings
Restore the traces configuration to its default settings.
Procedure
From the menu, select Configure > Cluster Settings, and select the Support tab.
In the Traces section, select Restore traces default settings. Then, in the confirmation message, select Yes.
Protocols debug level
The Protocols Debug Level section displays the debug level for the S3, NFS, and SMB protocols. If a protocol is not configured, the section indicates it, and you cannot change its debug level.
Change S3 debug level
If the S3 protocol is configured, you can change the debug level for all servers or specified servers.
The available debug levels are:
0 - CRITICAL
1 - ERROR
2 - WARNING
3 - INFO
4 - DEBUG
5 - TRACE
Procedure
From the menu, select Configure > Cluster Settings, and select the Support tab.
In the Protocols Debug Level section, select Change S3 debug level.
In the Update S3 Debug Level dialog, set the following properties:
Level: Select the debug level.
All servers: To apply the update to all servers, switch to On. To apply the update to specific servers, switch to Off and select the required servers.
Select Save.
In the Confirm S3 debug level change message, select Yes.
Change NFS debug level
If the NFS protocol is configured, you can change the debug level for all servers or specified servers.
The available debug levels are:
1 - EVENT
2 - INFO
3 - DEBUG
4 - MID DEBUG
5 - FULL DEBUG
Procedure
From the menu, select Configure > Cluster Settings, and select the Support tab.
In the Protocols Debug Level section, select Change NFS debug level.
In the Update NFS Debug Level dialog, set the following properties:
Level: Select the debug level.
All servers: To apply the update to all servers, switch to On. To apply the update to specific servers, switch to Off and select the required servers.
Select Save.
In the Confirm NFS debug level change message, select Yes.
Change SMB debug level
If the SMB protocol is configured, you can change the debug level for all servers or specified servers.
The available debug levels are:
0 - NO DEBUG
5 - MID DEBUG
10 - FULL DEBUG
Procedure
From the menu, select Configure > Cluster Settings, and select the Support tab.
In the Protocols Debug Level section, select Change SMB debug level.
In the Update SMB Debug Level dialog, set the following properties:
Level: Select the debug level.
All servers: To apply the update to all servers, switch to On. To apply the update to specific servers, switch to Off and select the required servers.
Select Save.
In the Confirm SMB debug level change message, select Yes.
Last updated